D1 Safety Equipment Distributors

TELESCOPIC ALUMINUM MODULAR CONSTRUCTION STAIR SYSTEM. ECONOMIC REVOLUTIONARY STAIR SYSTEM THAT AVOIDS RECURRING EXPENSES OF SINGLE USE STAIRS AND THEIR LIMITED LIFE SPAN.

The Accu-Fit Mobile GuardRail System is an OSHA compliant passive fall-protection system. The Accu-Fit railing system is designed to be used at or around leading edge fall hazard areas to prevent workers from being exposed to the fall hazard itself. The Accu-Fit railing system is constructed with schedule 40 galvanized pipe and pipe fittings that form a continuous, uniform railing profile which provides pleasing sight lines to compliment building architecture. The Accu-Fit system is available in three upright stanchion configurations namely, straight and two curved profiles. All three of these stanchion options are supported in freestanding cast iron base plates which require no mechanical attachment to the roof. The Accu-Fit railing system can be thought of as an assemble-on-site railing package. The horizontal railing pipes are sold in 21 foot lengths and held in place on the stanchion with structural pipe fittings. At corners or termination points, the pipe is trimmed to size in the field for a precise fit, hence the name, Accu-Fit. Stanchions are pinned into the base, forming a ballasted railing system designed to meet OSHA fall protection standards. The Accu-Fit Mobile GuardRail System comes standard in a galvanized finish but may be ordered with a powder coat topcoat to match building facades. Using the Accu-Fit Mobile Guardrail at Rooftop Perimeters: On flat commercial roofs, OSHA states that there is no "safe distance" from the roof edge. This speaks volumes about just how hazardous these areas can be. But the reality is that access to the roof edge or close proximity to it is necessary at times. So what should you do? The best solution is to provide a barrier fall protection system between the fall hazard and the area where the worker is working, thereby surrounding them in an OSHA-compliant enclosure. In other words, isolate people from the hazard.

The Accu-Fit Mobile GuardRail System is an OSHA compliant passive fall-protection system. The Accu-Fit railing system is designed to be used at or around leading edge fall hazard areas to prevent workers from being exposed to the fall hazard itself. The Accu-Fit railing system is constructed with schedule 40 galvanized pipe and pipe fittings that form a continuous, uniform railing profile which provides pleasing sight lines to compliment building architecture. The Accu-Fit system is available in three upright stanchion configurations namely, straight and two curved profiles. All three of these stanchion options are supported in freestanding cast iron base plates which require no mechanical attachment to the roof. The Accu-Fit railing system can be thought of as an assemble-on-site railing package. The horizontal railing pipes are sold in 21 foot lengths and held in place on the stanchion with structural pipe fittings. At corners or termination points, the pipe is trimmed to size in the field for a precise fit, hence the name, Accu-Fit. Stanchions are pinned into the base, forming a ballasted railing system designed to meet OSHA fall protection standards. The Accu-Fit Mobile GuardRail System comes standard in a galvanized finish but may be ordered with a powder coat topcoat to match building facades. Using the Accu-Fit Mobile Guardrail at Rooftop Perimeters: On flat commercial roofs, OSHA states that there is no "safe distance" from the roof edge. This speaks volumes about just how hazardous these areas can be. But the reality is that access to the roof edge or close proximity to it is necessary at times. So what should you do? The best solution is to provide a barrier fall protection system between the fall hazard and the area where the worker is working, thereby surrounding them in an OSHA-compliant enclosure. In other words, isolate people from the hazard. Barrier systems such as the Accu-Fit Mobile Guardrail System allow workers to go about their work without being tethered to an OSHA-compliant fixed or mobile anchorage device. This freedom of movement greatly increases worker productivity and takes the headache of worker compliance and training out of the equation. The Accu-Fit Mobile Guardrail System can be installed along entire roof perimeters, providing a comprehensive, 100% fall protection solution. Alternatively, it can be installed just around specific equipment or access points where people will be working. How many different people access your roof to do maintenance or inspections? Probably more than you think. Our fall protection systems will give you peace of mind, knowing that the Accu-fit Mobile Guardrail System is always there, always protecting against the unthinkable.

The Accu-Fit Mobile GuardRail System is an OSHA compliant passive fall-protection system. The Accu-Fit railing system is designed to be used at or around leading edge fall hazard areas to prevent workers from being exposed to the fall hazard itself. The Accu-Fit railing system is constructed with schedule 40 galvanized pipe and pipe fittings that form a continuous, uniform railing profile which provides pleasing sight lines to compliment building architecture. The Accu-Fit system is available in three upright stanchion configurations namely, straight and two curved profiles. All three of these stanchion options are supported in freestanding cast iron base plates which require no mechanical attachment to the roof. The Accu-Fit railing system can be thought of as an assemble-on-site railing package. The horizontal railing pipes are sold in 21 foot lengths and held in place on the stanchion with structural pipe fittings. At corners or termination points, the pipe is trimmed to size in the field for a precise fit, hence the name, Accu-Fit. Stanchions are pinned into the base, forming a ballasted railing system designed to meet OSHA fall protection standards. The Accu-Fit Mobile GuardRail System comes standard in a galvanized finish but may be ordered with a powder coat topcoat to match building facades. Using the Accu-Fit Mobile Guardrail at Rooftop Perimeters: On flat commercial roofs, OSHA states that there is no "safe distance" from the roof edge. This speaks volumes about just how hazardous these areas can be. But the reality is that access to the roof edge or close proximity to it is necessary at times. So what should you do? The best solution is to provide a barrier fall protection system between the fall hazard and the area where the worker is working, thereby surrounding them in an OSHA-compliant enclosure. In other words, isolate people from the hazard. Barrier systems such as the Accu-Fit Mobile Guardrail System allow workers to go about their work without being tethered to an OSHA-compliant fixed or mobile anchorage device. This freedom of movement greatly increases worker productivity and takes the headache of worker compliance and training out of the equation. The Accu-Fit Mobile Guardrail System can be installed along entire roof perimeters, providing a comprehensive, 100% fall protection solution. Alternatively, it can be installed just around specific equipment or access points where people will be working. How many different people access your roof to do maintenance or inspections? Probably more than you think. Our fall protection systems will give you peace of mind, knowing that the Accu-fit Mobile Guardrail System is always there, always protecting against the unthinkable. Advantages of Accu-Fit Mobile Railings Meets and exceeds OSHA regulations for fall protection. Tested and independently certified to be in accordance with OSHA fall protection for guardrail regulations, sections 1910.23 & 1926.500–1926.503. Allows customized installation — railing sections provided in 21 foot lengths (or shorter if needed) to allow custom fabrication of guard rails in field for precise fit. Railing will be 42" tall in the base. Constructed of 1 1/4" schedule 40 galvanized pipe secured with structural pipe fittings for heavy duty construction and continuous railing profiles for pleasing sight lines. Choice of vertical or curved stanchions. Highly effective as OSHA compliant hazard barrier. Commonly used for rooftop fall protection, new building construction, mezzanines, in-plant guarding, and more. Request a Quote:

For whatever reason you need to access trucks and other heavy vehicles, there are dangerous ways to do it, or SafeSmart’s safe and efficient way. During maintenance or when handling goods, the fall danger is always there – and with falls from lower heights accounting for most workplace injuries and deaths in Canada, it shows that standard ladders and general clambering are the culprits. With a self-closing gate at the entrance to the platform, 45-degree stair access, ultra-strong rails and free-wheeling lockable castors, this system easily wheels up to the vehicle’s edge, giving the worker a lot more room to stand whilst at height, with much more access to the vehicle’s sides for cargo handling, securing a load, maintenance, anything. And for challenging environments such as in cold and icy conditions, the 8.6"-deep braced stair treads feature a non-slip surface. Also includes lifting points for easy craning and forklift channels for being able to move the unit to other sites.

Need a quick way to give workers a visual warning of a potential hazardous area, but don't want to use orange cones to do it? Try the Never Rust Permanent Warning Line system. This visual warning line system is a completely non-metal guarding solution, featuring a 30 lb. recycled rubber base plate and aluminum stanchion. The system can carry a variety of flagged line. When using heavier flagged line for wind-prone areas, simply move stanchions closer together to maintain proper warning line height of 34"–39" above the walking surface as prescribed by OSHA.

EnduraLine Mobile is our most robust warning line system yet for permanent demarcation of hazardous areas. Cast iron base plates, steel stanchions, and plastic-coated galvanized cable with aluminum pennants means the EnduraLine warning line system is built for long-term exposure to the elements. The EnduraLine Mobile system goes a step further. This non-penetrating warning line system is also designed to integrate perfectly with our D1-360 Mobile railing system. The minimum OSHA requirement for warning line is that they be placed 15’ feet or more away from a leading edge. Any closer to the leading edge, and fall protection railings or other fall protection devices must be provided. EnduraLine combined with our SRC 360 Mobile Rail answer both requirements and provide a complete, comprehensive, OSHA-compliant perimeter guarding solution.

This Never-Rust Visual Warning Line Safety Cone acts as low-cost, OSHA-compliant method of alerting workers of a fall hazard area. 42-inch tall, high-impact, low-density polyethylene channelizing cone Holds flags at 39" on stanchions 30 lb. recycled rubber base Can accommodate a variety of flagged line Reinforced easy-grip loop handle Stackable with or without bases Safety orange color with ultraviolet stabilizer for fade resistance Meets federal MUTCD and OSHA standards

The D1 Safety Mobile Restraint System is an ideal non-penetrating mobile restraint solution. Consists of six 108-lb. bases with a 5000-lb. attachment point. Can be broken down for easy transportation. Intended as a fall restraint system to prevent a worker from reaching a fall hazard.

Permanent safety guardrails for fall protection comes in many shapes and sizes to address worksite needs. Our permanent mount safety guardrails offer the customer choices in length, height and mounting options. One of the most unique features of our guard rail systems is that they can be removed from the railing holder if needed. By simply pulling a pin, the railing section can be removed from the base plate. The only thing that remains in place is the railing holder itself. This flexibility greatly increases productivity by having fall protection in place when you need it and removed for access when it might otherwise be in the way. We offer floor mounted safety railing systems which can used in many areas like, loading docks, shipping pits, crowd control, access control to name a few. We also offer wall mounted guardrail systems. The guardrails mount to the vertical wall of a leading edge hazard. Shipping pits are a good example of installing safety railing holders on the inside vertical wall of the pit and inserting the railings into the holders. This eliminates anything mounted to your walking surface. To remove the railing, pull the pin and lift out the railings. This allows free and clear access to the truck in the shipping pit. We even do structural railing systems designed to mount permanently to a structure without the need for removal.

Permanent safety guardrails for fall protection comes in many shapes and sizes to address worksite needs. Our permanent mount safety guardrails offer the customer choices in length, height and mounting options. One of the most unique features of our guard rail systems is that they can be removed from the railing holder if needed. By simply pulling a pin, the railing section can be removed from the base plate. The only thing that remains in place is the railing holder itself. This flexibility greatly increases productivity by having fall protection in place when you need it and removed for access when it might otherwise be in the way. We offer floor mounted safety railing systems which can used in many areas like, loading docks, shipping pits, crowd control, access control to name a few. We also offer wall mounted guardrail systems. The guardrails mount to the vertical wall of a leading edge hazard. Shipping pits are a good example of installing safety railing holders on the inside vertical wall of the pit and inserting the railings into the holders. This eliminates anything mounted to your walking surface. To remove the railing, pull the pin and lift out the railings. This allows free and clear access to the truck in the shipping pit. We even do structural railing systems designed to mount permanently to a structure without the need for removal.

Our portable, free-standing safety railing and guardrail systems meet and exceed OSHA regulations for fall protection compliance. Each one of our fall protection products support our unwavering commitment at D1 Safety to help ensure that your work environment is safe, secure and productive. Each one of our safety products are tested and certified to meet or exceed OSHA standards for fall protection. More specifically, our portable, non-penetrating guard rails are classified as hazard barriers by acting as a physical barrier between the worker and the fall hazard. Common applications are flat roof fall protection along the leading edge of roof perimeters, ladder access points, roof hatches, skylight guarding and more. Our guard rail systems are also used on loading docks, shipping pit protection, warehouse traffic lanes, crowd control, pier and rail yard protection and much more. We take pride in our portable guard rail design. Each safety guardrail system is simple to install and versatile in the respect that they can be set up in a number of different configurations to fit within your existing infrastructure. Once installed, workers are free to move about inside the perimeter without the need of being tied off to an approved anchorage device as with harnesses and lanyards. This allows for complete freedom of movement of secured personnel. You can rest assured that here at D1 Safety, our professional sales and engineering staff is here to help in meeting your specific fall protection requirements. We also provide custom colors and galvanized finishes. Our design and engineering teams work hard to ensure that our safety products meet the highest product quality and performance standards. Give us a call today with any questions you may have. D1 Safety is here to support your business by making your work environment safe, secure and OSHA compliant.

Skylight safety is one of the most often overlooked fall hazards on buidlings. Industrial and commercial skylights have long been architectural features that do everything from illuminating dark areas in industrial facilities to adding beauty and elegance to indoor commercial spaces. While function and beauty are important elements in a buildings’ design, without proper guarding skylights can pose a serious fall hazard risk often resulting in injury and fatalities. In fact, the hazard is so high that OSHA makes no distinction between an unguarded skylight and an open hole in the roof and therefore mandates that all skylights either must be rated for fall protection in their design or they must be covered with a protective guard that will prevent a fall through the skylight. Skylights comes in a variety of shapes, sizes and configurations. To meet this variety, D1 Safety offers a wide range of protective skylight screens and guards that restore skylights back into OSHA compliance. Each guarding option comes with its own features and benefits to meet custom requirements often found on buildings. All of our products meet the appropriate standards and are made in the USA by AWS Certified Welders under strict quality control standards.

We Distribute All Types of Cantilever Gates for Dock Areas to Mezzanines Contact Us for your next gate.

Roof Hatch Railing Guards are your first line of defense against a fall through an open roof hatch and unguarded roof hatches are an OSHA violation. Rooftop roof hatches, scuttle hatches and stairway hatches all have one thing in common on flat roofs in that they all represent a significant fall hazard when left open. When workers are up on the roof the cover is commonly left open so the worker is not accidentally locked out of the building. This open door scenario also leaves a gaping hole in the roof through which workers can and do fall through often to disastrous consequences. Safety Rail Company addresses roof hatch safety by providing an OSHA compliant guard around the hatch. Our freestanding roof hatch guard slips right over the top of the roof hatch and compression fits up against the curb of the hatch. Non-penetrating design eliminates any holes in the roof and roof hatch. Our Roof Hatch guard also features grab bars for safe ingress/egress, a self-closing gate and a 2-foot safe landing zone for workers to safely enter and exit the roof hatch opening. A variety of sizes and finishes are available to meet your needs.

MOUNT: This gate will mount to 1"-2" round-post or 1"-2" square-post material. OPENING: This gate adjusts to fit any opening between 30" and 36". FINISH: This gate is finished with a durable powder-coated safety yellow. WEIGHT: This gate weighs 133 lbs. CERTIFICATIONS: This gate is OSHA-compliant and made in the USA by AWS-certified welders.